View LZ0P3615_1401418.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

in the absence of confirmation by device specification sheets, sharp takes no responsibility for any defects that may occur in equipment using any sharp devices shown in catalogs, data books, etc. contact sharp in order to obtain the latest device specification sheets before using any sharp device. 1 description the lz0p3610/11/12 o /15 o are 1/4-type (4.5 mm) 270 000-pixel built-in lens color ccd (charge- coupled device) area sensors. with their small lens and wlcc-type flat package, it is possible to make ultra small color camera easily. features number of effective pixels : 512 (h) x 492 (v) number of optical black pixels e horizontal : 2 front and 28 rear pixel pitch : 7.2 m (h) x 5.6 m (v) mg, g, cy, and ye complementary color filters low fixed-pattern noise and lag blooming suppression structure built-in output amplifier built-in overflow drain voltage circuit and reset gate voltage circuit horizontal shift register clock and reset gate clock voltage : 3.3 v (typ.) variable electronic shutter (1/60 to 1/10 000 s) compatible with ntsc standard built-in optical low-pass-filter integrated lens : horizontal viewing angle lz0p3610 : 52? lz0p3611 : 50? olz0p3612 : 62? oLZ0P3615 : 115? package e 14-pin half-pitch wlcc * type e base section size : 12 mm (h) x 11 mm (v) e outline dimensions (max.) : 18 mm (h) x 11 mm (v) package height e approx. 10 mm (single lens) : lz0p3610 e approx. 13 mm (two pcs. of lenses) : lz0p3611/12 o /15 o * window leadless chip carrier pin connections lz0p3610/3611/3612/3615 lz0p3610/3611/ 3612 o /3615 o 1/4-type built-in lens color ccd area sensors with 270 k pixels ounder development od rs nc 1 os nc 2 h2 h1 1 2 3 4 5 6 7 14 13 12 11 10 9 8 gnd v4 v3 v2 v1 pw ofd 14-pin half-pitch wlcc type top view lz0p3610 horizontal viewing angle lens specification characteristics package height number of integrated lenses oLZ0P3615olz0p3612lz0p3611 52? 115? 62?50? approx. 10 mm single two pcs. approx. 13 mm refer to each following specification. comparison table
2 lz0p3610/3611/3612/3615 pin description absolute maximum ratings (t a = +25 ?c) symbol pin name od output transistor drain os output signals rs reset transistor clock v1 , v2 , v3 , v4 vertical shift register clock h1 , h2 horizontal shift register clock ofd overflow drain pw p-well gnd ground nc 1 , nc 2 no connection parameter symbol rating unit output transistor drain voltage v od 0 to +18 v overflow drain voltage v ofd internal output v reset gate clock voltage v rs internal output v vertical shift register clock voltage v v e10.5 to +17.5 v horizontal shift register clock voltage v h e0.3 to +12 v voltage difference between p-well and vertical clock v pw -v v e28 to 0 v voltage difference between vertical clocks v v -v v 0 to +15 v e20 to +70 ?c storage temperature t stg e10 to +60 ?c ambient operating temperature t opr 3 2 1 note notes : 1. do not connect to dc voltage directly. when ofd is connected to gnd, connect v od to gnd. overflow drain clock is applied below 26 vp-p. 2. do not connect to dc voltage directly. when rs is connected to gnd, connect v od to gnd. reset gate clock is applied below 8 vp-p. 3. when clock width is below 10 s, and clock duty factor is below 0.1%, voltage difference between vertical clocks will be below 27 v.
3 lz0p3610/3611/3612/3615 recommended operating conditions parameter symbol min. typ. max. unit note ambient operating temperature t opr 25.0 ?c output transistor drain voltage v od 14.55 15.0 15.45 v overflow drain clock p-p level 23.5 v 1 v ofd 21.5 ground gnd 0.0 v p-well voltage v pw e9.0 v vl v2 vertical shift register clock low level v v1l , v v2l v v3l , v v4l e8.5 e8.0 e7.5 v intermediate level v v1i , v v2i v v3i , v v4i 0.0 v high level v v1h , v v3h 14.55 15.0 15.45 v horizontal shift register clock low level v h1l , v h2l e0.05 0.0 0.05 v high level v h1h , v h2h 3.0 3.3 5.25 v reset gate clock p-p level v rs v1 vertical shift register clock frequency f v1 , f v2 f v3 , f v4 15.73 khz horizontal shift register clock frequency f h1 , f h2 9.53 mhz reset gate clock frequency f rs 9.53 mhz notes : connect nc 1 and nc 2 to gnd directly or through a capacitor larger than 0.047 f. 1. use the circuit parameter indicated in "system configuration example" , and do not connect to dc voltage directly. 2. v pw is set below v vl that is low level of vertical shift register clock, or is used with the same power supply that is connected to v l of v driver ic. * to apply power, first connect gnd and then turn on v od . after turning on v od , turn on pw first and then turn on other powers and pulses. do not connect the device to or disconnect it from the plug socket while power is being applied. 3.0 3.3 5.25
4 lz0p3610/3611/3612/3615 characteristics for lz0p3610 (drive method : field accumulation) ( t a : +25 ?c, operating conditions : the typical values specified in "recommended operating conditions" . color temperature of light source : 3 200 k) lens specification for lz0p3610 notes : 1. the average output voltage in the central area (h/10, v/10) under uniform illumination. the standard exposure conditions are defined as when v o is 150 mv. 2. the average output voltage in the central area (h/10, v/10) under 10 times exposure of the standard exposure conditions. 3. the average output voltage in the central area (h/10, v/10) when a 1 000 lux light source with a white board of 90% reflector is imaged. 4. the resolution in the central area (h/10, v/10) at which the image of the tv resolution chart (ex. eiaj test chart) can be distinguished on the b/w video monitor. 5. the resolution in the peripheral area (image height : y = 0.8) under the conditions mentioned above. 6. defined by the following formula at the brightness of standard output voltage : (vco/vce) x 100 [%] vco : output voltage at edge of the image (at video output). vce : output voltage at center of the image (at video output). 7. the difference between the center position of image and that of the monitor. this is the ratio for the horizontal underscanning monitor size which includes the decentering eccentricity when turning the lens head one time. parameter symbol standard output voltage v o saturation output voltage v sat 700 min. typ. 150 500 400 r sensitivity 3 2 1 note mv mv mv unit max. 8.0 ma output transistor drain current i od 4.0 %6 shading 50 65 tv line 4 resolution (at center) 250 300 parameter specification construction single (non-spherical, plastic) focal length 4.0 mm [typ. : reference] note 2.85% f no. focus adjustment range to 10 cm 2 tv distortion 2 e3.2% 1 viewing angle h : 52?, v : 40?, diagonal : 65? [typ. : reference] notes : 1. tv distortion is defined by the formula, (?y/y) x 100 [%] at capturing rectangular pattern sized horizontal by vertical as 4 by 3. "y" is defined as the vertical height of the center of the horizontal line. ?y is defined as the difference between the vertical height of the center of the horizontal line and an edge of it. 2. the best focus point of an object can be obtained by turning the lens head within this range. 3. torques which are necessary for turning the lens. * be careful not to remove the lens head by turning it counterclockwise too much when adjusting macro. y ?y 200 150 resolution (at corner) 5 tv line difference of center position 7 % 10 3 0.00005 to 0.001 nm torque of focusing
5 lz0p3610/3611/3612/3615 characteristics for lz0p3611 (drive method : field accumulation) ( t a : +25 ?c, operating conditions : the typical values specified in "recommended operating conditions" . color temperature of light source : 3 200 k) lens specification for lz0p3611 notes : 1. the average output voltage in the central area (h/10, v/10) under uniform illumination. the standard exposure conditions are defined as when v o is 150 mv. 2. the average output voltage in the central area (h/10, v/10) under 10 times exposure of the standard exposure conditions. 3. the average output voltage in the central area (h/10, v/10) when a 1 000 lux light source with a white board of 90% reflector is imaged. 4. the resolution in the central area (h/10, v/10) at which the image of the tv resolution chart (ex. eiaj test chart) can be distinguished on the b/w video monitor. 5. the resolution in the peripheral area (image height : y = 0.8) under the conditions mentioned above. 6. defined by the following formula at the brightness of standard output voltage : (vco/vce) x 100 [%] vco : output voltage at edge of the image (at video output). vce : output voltage at center of the image (at video output). 7. the difference between the center position of image and that of the monitor. this is the ratio for the horizontal underscanning monitor size which includes the decentering eccentricity when turning the lens head one time. parameter symbol standard output voltage v o saturation output voltage v sat 700 min. typ. 150 500 400 r sensitivity 3 2 1 note mv mv mv unit max. 8.0 ma output transistor drain current i od 4.0 %6 shading 40 60 tv line 4 resolution (at center) 250 300 parameter specification construction 2 pcs. (non-spherical, plastic) focal length 3.9 mm [typ. : reference] note 2.85% f no. focus adjustment range to 10 cm 2 tv distortion 2 e1.0% 1 viewing angle h : 50?, v : 38?, diagonal : 60? [typ. : reference] notes : 1. tv distortion is defined by the formula, (?y/y) x 100 [%] at capturing rectangular pattern sized horizontal by vertical as 4 by 3. "y" is defined as the vertical height of the center of the horizontal line. ?y is defined as the difference between the vertical height of the center of the horizontal line and an edge of it. 2. the best focus point of an object can be obtained by turning the lens head within this range. 3. torques which are necessary for turning the lens. * be careful not to remove the lens head by turning it counterclockwise too much when adjusting macro. y ?y 200 150 resolution (at corner) 5 tv line difference of center position 7 % 10 3 0.00005 to 0.001 nm torque of focusing
6 lz0p3610/3611/3612/3615 characteristics for lz0p3612 o (drive method : field accumulation) ( t a : +25 ?c, operating conditions : the typical values specified in "recommended operating conditions" . color temperature of light source : 3 200 k) lens specification for lz0p3612 o notes : 1. the average output voltage in the central area (h/10, v/10) under uniform illumination. the standard exposure conditions are defined as when v o is 150 mv. 2. the average output voltage in the central area (h/10, v/10) under 10 times exposure of the standard exposure conditions. 3. the average output voltage in the central area (h/10, v/10) when a 1 000 lux light source with a white board of 90% reflector is imaged. 4. the resolution in the central area (h/10, v/10) at which the image of the tv resolution chart (ex. eiaj test chart) can be distinguished on the b/w video monitor. 5. the resolution in the peripheral area (image height : y = 0.8) under the conditions mentioned above. 6. defined by the following formula at the brightness of standard output voltage : (vco/vce) x 100 [%] vco : output voltage at edge of the image (at video output). vce : output voltage at center of the image (at video output). 7. the difference between the center position of image and that of the monitor. this is the ratio for the horizontal underscanning monitor size which includes the decentering eccentricity when turning the lens head one time. parameter symbol standard output voltage v o saturation output voltage v sat 700 min. typ. 150 500 400 r sensitivity 3 2 1 note mv mv mv unit max. 8.0 ma output transistor drain current i od 4.0 %6 shading 50 tv line 4 resolution (at center) 250 300 parameter specification construction 2 pcs. (non-spherical, plastic) focal length 3.0 mm [typ. : reference] note 2.85% f no. focus adjustment range to 10 cm 2 tv distortion 2 e1.0% 1 viewing angle h : 62?, v : 49?, diagonal : 74? [typ. : reference] notes : 1. tv distortion is defined by the formula, (?y/y) x 100 [%] at capturing rectangular pattern sized horizontal by vertical as 4 by 3. "y" is defined as the vertical height of the center of the horizontal line. ?y is defined as the difference between the vertical height of the center of the horizontal line and an edge of it. 2. the best focus point of an object can be obtained by turning the lens head within this range. 3. torques which are necessary for turning the lens. * be careful not to remove the lens head by turning it counterclockwise too much when adjusting macro. y ?y 200 150 resolution (at corner) 5 tv line difference of center position 7 % 10 3 0.00005 to 0.001 nm torque of focusing ounder development
7 lz0p3610/3611/3612/3615 characteristics for LZ0P3615 o (drive method : field accumulation) ( t a : +25 ?c, operating conditions : the typical values specified in "recommended operating conditions" . color temperature of light source : 3 200 k) lens specification for LZ0P3615 o notes : 1. the average output voltage in the central area (h/10, v/10) under uniform illumination. the standard exposure conditions are defined as when v o is 150 mv. 2. the average output voltage in the central area (h/10, v/10) under 10 times exposure of the standard exposure conditions. 3. the average output voltage in the central area (h/10, v/10) when a 1000 lux light source with a white board of 90% reflector is imaged. 4. the resolution in the central area (h/10, v/10) at which the image of the tv resolution chart (ex. eiaj test chart) can be distinguished on the b/w video monitor. 5. the resolution in the peripheral area (image height : y = 0.8) under the conditions mentioned above. 6. defined by the following formula at the brightness of standard output voltage : (vco/vce) x 100 [%] vco : output voltage at edge of the image (at video output). vce : output voltage at center of the image (at video output). 7. the difference between the center position of image and that of the monitor. this is the ratio for the horizontal underscanning monitor size which includes the decentering eccentricity when turning the lens head one time. parameter symbol standard output voltage v o saturation output voltage v sat 700 min. typ. 150 500 400 r sensitivity 3 2 1 note mv mv mv unit max. 8.0 ma output transistor drain current i od 4.0 %6 shading 45 tv line 4 resolution (at center) 300 parameter specification construction 2 pcs. (non-spherical, plastic) focal length 1.53 mm [typ. : reference] note 2.85% f no. focus adjustment range to 10 cm 2 tv distortion 2 e14% 1 viewing angle h : 115?, v : 89?, diagonal : 138? [typ. : reference] notes : 1. tv distortion is defined by the formula, (?y/y) x 100 [%] at capturing rectangular pattern sized horizontal by vertical as 4 by 3. "y" is defined as the vertical height of the center of the horizontal line. ?y is defined as the difference between the vertical height of the center of the horizontal line and an edge of it. 2. the best focus point of an object can be obtained by turning the lens head within this range. 3. torques which are necessary for turning the lens. * be careful not to remove the lens head by turning it counterclockwise too much when adjusting macro. y ?y 200 resolution (at corner) 5 tv line difference of center position 7 % 10 3 0.00005 to 0.001 nm torque of focusing ounder development
lz0p3610/3611/3612/3615 8 pixel structure 512 (h) x 492 (v) 1 pin optical black (2 pixels) optical black (28 pixels) color filter array mg g mg g mg cy ye cy ye cy g mg g mg g cy ye cy ye cy mg g mg g mg cy ye cy ye cy mg g mg g mg ye cy ye cy ye g mg g mg g ye cy ye cy ye mg g mg g mg ye cy ye cy ye g mg g mg g ye cy ye cy ye mg g mg g mg ye cy ye cy ye g mg g mg g ye cy ye cy ye g mg g mg g cy ye cy ye cy mg g mg g mg cy ye cy ye cy g mg g mg g cy ye cy ye cy (1, 492) (512, 492) (1, 1) (512, 1) even field odd field
lz0p3610/3611/3612/3615 9 timing chart 484 + 485 486 + 487 488 + 489 490 + 491 492 1 + 2 3 + 4 5 + 6 7 + 8 9 + 10 11 + 12 os ofd v4 v3 v2 v1 vd hd (odd field) shutter speed 1/2 000 s vertical transfer timing 483 + 484 485 + 486 487 + 488 489 + 490 491 + 492 1 2 + 3 4 + 5 6 + 7 8 + 9 10 + 11 os ofd v4 v3 v2 v1 vd hd (even field) 525 1 10 17 19 263 272 279 282 os rs h2 h1 hd 512 ob (28) ob (2) ofd v4 v3 v2 v1 horizontal transfer timing 29 606, 1 60 24 54 34 64 62 72 49 39 59 output (512) 1 1111111
lz0p3610/3611/3612/3615 10 v4 v3 v2 v1 hd (odd field) (even field) readout timing v4 v3 v2 v1 hd 1 29 39 24 34 64 54 59 161 180 290 338 242 290 449 606, 1 60 29 39 54 64 34 59 49 49 60 1 29 39 24 34 64 54 59 161 180 290 338 242 290 606, 1 60 54 64 450 59 49 60
lz0p3610/3611/3612/3615 11 system configuration example od os nc 1 ofd pw rs h2 h1 gnd v4 v3 v2 v1 nc 2 v 3b v 3a v 1b v 1a v ma v h v 4 v 2 v l v mb pofd nc v h v od v 4x v l (v pw ) v 3x v 2x v 1x vh 3ax vh 1ax +5 v ofdx h1 h2 rs ccd out 0.01 f 1 m$ v ofdh vh 3bx ofdx v 2x v 1x v 3x v dd gnd v 4x vh 3ax vh 1bx vh 1ax + + 1 2 3 4 5 6 7 8 12 24 23 22 21 20 19 18 17 13 11 14 10 15 9 16 1 2 3 4 5 6 7 14 13 12 11 10 9 8 lr36685 lz0p361x 270 pf 1 m$ 100 $ 0.1 f + + (*1) (*1) (*1) rs , ofd : use the circuit parameter indicated in this circuit example, and do not connect to dc voltage directly.
packages for ccd and cmos devices 12 18 11 5.0 0.1 approx. 10 2-0.8 0.8 2-c0.2 14 0.1 12 4-90? 5.0 0.1 approx. 10 11.0 0.05 height 0.5 1.0 0.1 1.0 0.1 11.0 0.05 7.6 0.05 3.6 1.27 0.64 1.6 1.27 +0 e0.2 +0 e0.1 +0 e0.05 +0 e0.05 +0 e0.1 +0 e0.05 +0 e0.05 11.0 12.0 +0 e0.1 +0 e0.1 no.1 index 1.0 +0 e0.1 2.0 0.1 2.0 0.1 no.1 index 14 wlcc type applicable models lz0p3610/ lz0p3620 packages (unit : mm) 18 11 3.0 0.1 5.0 0.1 approx.12-13 2-0.8 0.8 1.6 2-c0.2 14 0.1 12 4-90? 5.0 0.1 approx. 12 11.0 0.05 height 0.5 3.0 0.1 1.0 0.1 2.0 0.1 11 0.05 7.6 0.05 3.6 1.27 0.64 1.27 2.0 0.1 +0 e0.2 +0 e0.1 +0 e0.05 +0 e0.05 +0 e0.05 +0 e0.1 +0 e0.05 no.1 index 11.0 12.0 +0 e0.05 +0 e0.05 no.1 index 14 wlcc type applicable models lz0p3611/12/15, lz0p3621/22/25, lz0p3641/42/45/46
precautions for built-in lens ccd area sensors 13 precautions for built-in lens ccd area sensors 1. package breakage in order to prevent the package, the lens holder, and the lens from being broken, follow the instructions below : 1) the ccd is a precise optical component and the package-base material is ceramic. therefore, ? take care not to drop the device when mounting, handling, or transporting. ? avoid giving a shock to the package. especially when leads are fixed to the socket or the circuit board, a small shock could break the package more easily than when the package isn?t fixed. 2) when adjusting the focus, screw the lens holder to the circuit board before soldering the leads. at that time, make sure to use a circuit board with plenty of strength, and to avoid the package and the lens holder from being broken, the following screw and clamp torque are recommended. ? recommended mounting screw : 1.7 tapping screw (b-tight type), length, l = the thickness of the circuit board + 5 mm ? recommended clamp torque : 0.012 nm [however, when the thickness of the circuit board is thinner than t = 2.0 mm] 3) if any damage or breakage occurs on the surface of the lens, its characteristics could deteriorate. therefore, ? do not hit the lens. ? do not give a shock large enough to cause distortion. ? do not scrub or scratch the surface of the lens. e even a soft cloth or applicator, if dry, could cause dust to scratch the lens. 2. electrostatic damage as compared with general mos-lsi, ccd has lower esd. therefore, take the following anti-static measures when handling the ccd : 1) always discharge static electricity by grounding the human body and the instrument to be used. to ground the human body, provide resistance of about 1 m$ between the human body and the ground to be on the safe side. 2) when directly handling the device with the fingers, hold the lens holder and do not touch the lead. 3) to avoid generating static electricity, a. do not scrub the device with cloth or plastic. b. do not attach any tape or labels. c. do not clean the device with dust-cleaning tape. 4) when storing or transporting the device, put it in a container of conductive material. 3. dust and contamination dust or contamination on the surface of the lens and the inside of the lens holder could deteriorate the output characteristics or cause a scar. in order to minimize dust or contamination on the device, take the following precautions : 1) do not remove the lens from the body. especially when adjusting macro, be careful not to remove the lens by turning it counter- clockwise too much. 2) do not touch the surface of the lens with the fingers. if dust or contamination gets on the surface of the lens, the following cleaning method is recommended : ? handle the built-in lens ccd in a clean environment such as a cleaned booth. (the cleanliness level should be, if possible, class 1 000 at least.)
e in case where the soldering may exceed the time mentioned above, resume the work after the device returns to normal temperature. ? do not put too much force onto the lens and the lens holder while soldering. ? be careful not to let the soldering iron touch the lens holder. e soldering can be quickly/neatly done by laying the soldering iron so it lightly touches the border between the package and the circuit board and sliding it in sideways. 2) there is no guarantee of the performance of the device which has been removed or resoldered after being soldered once under the conditions mentioned above. e in case there seems to be an inferior device, consult with our sales office before removing it. 3) avoid using or storing the ccd at high temperature or high humidity as it is a precise optical component. do not give a mechanical shock to the ccd. 4) do not expose the device to strong light. for the color device, long exposure to strong light will fade the color of the color filters. ? dust from static electricity should be blown off with an ionized air blower. for anti- electrostatic measures, however, ground all the leads on the device before blowing off the dust. ? the contamination on the surface of the lens should be wiped off with a clean applicator soaked in isopropyl alcohol. wipe slowly and gently in one direction only. e frequently replace the applicator and do not use the same applicator to clean more than one device. ? make sure there is no dust or contamination on the lens and screw it on the lens holder. 4. other 1) soldering should be manually performed under the following conditions : ? use esd-measured soldering iron ? the conditions of the soldering time in which the soldering iron touches the package, differs by the shape and the temperature of the iron end. refer to the table below and take great care in soldering. the shape of the iron end below 275 ?c below 300 ?c below 350 ?c the temperature of the iron end soldering time time touching the package should be less than 40 seconds time touching the package should be less than 25 seconds time touching the package should be less than 35 seconds 17 r0.5 (unit : mm) 17 (unit : mm) 6.5 0.5 3.2 precautions for built-in lens ccd area sensors 14

▲Up To Search▲

Price & Availability of LZ0P3615

	To Download LZ0P3615 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .